Published by on August 22, 2021
Categories: Art

ASTM D Standard Test Method for Ball-Pan Hardness of Activated Carbon. Standard Test Method for Ball-Pan Hardness of Activated Carbon. Status: Withdrawn · Replaced by: ASTM D Buy this standard. Price: SEK. PDF. D()活性碳的球盘硬度的试验方法 – Designation: D Referenced Documents ASTM Standards: B 19 Speci?cation for.

Author: Kajilkis Taugor
Country: Costa Rica
Language: English (Spanish)
Genre: Software
Published (Last): 1 July 2017
Pages: 187
PDF File Size: 2.10 Mb
ePub File Size: 13.53 Mb
ISBN: 611-5-54097-476-6
Downloads: 3788
Price: Free* [*Free Regsitration Required]
Uploader: Voodoonos

Apparatus and Materials 6.

ASTM D3802 – 16

Humidity effects during a given test will largely cancel out if no change in humidity occurs between asstm. Place the hardness f3802 sieve on top of the receiving pan. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

Use additional material obtained as in 9. Current edition approved June 29, Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.

ASTM D – 10 Standard Test Method for Ball-Pan Hardness of Activated Carbon

Discard the fractions above the larger and below the smaller nominal particle size. Table 1 lists the hardness test sieve corresponding to each minimum nominal sieve. Fit the cover plate with a cork stopper which extends from 3. Shake with the hammer operating for 10 min 6 10 s. None of these has proved completely satisfactory for all applications, and all have been questioned by ASTM Committee D on Activated Carbon as tests atm establishing degradation resistance.


Pour the screened and weighed sample into the hardness pan and add the steel balls. The extra sieves, in this case, serve only to form a stack which?

Standard Test Method for Ball-Pan Hardness of Activated Carbon – CERN Document Server

Conceding the fact that the test does not actually measure in-service resistance to degradation, it can be used to establish the comparability of lots ostensibly of the same grade of carbon.

Weigh to the nearest 0. It is the responsibility of the user of this asrm to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Precision and Bias Asym adhesion of material to sieves, brushes, etc. Obtain at least mL of material within the nominal mesh size range.

Standard Test Method for Ball-Pan Hardness of Activated Carbon

BoxGastonia, NChas been found to be satisfactory. The value of H2 gives the upper limit of hardness, if we ignore the effects of humidity. One supplier tested 31 samples of a single grade of carbon and obtained an average hardness of Tyler Model SB, available from W.


Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM Headquarters. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

A superscript epsilon e indicates an editorial change since the last revision or reapproval. Sieves shall be calibrated at reasonable intervals in accordance with the procedure described in Speci?

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. At the end of this period, the amount of particle size degradation is aatm by measuring the quantity of carbon, by weight, which is retained on a sieve whose openings are closest to one half the openings of the sieve that de?

Summary of Test Method 4.

Adjust the bottom stops to give a clearance of approximately 1. A number in parentheses indicates the year of last reapproval.