Published by on August 21, 2021
Categories: Spiritual

AD Low Distortion. Differential RF/IF Amplifier. Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility. PCN Design/Specification, AD Datasheet Update 02/Oct/ AD EVALZ – Analog Devices Inc. | ADEVALZ-ND DigiKey Electronics; AD . ESD CAUTION. ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as V readily accumulate on the human body and test.

Author: JoJobar Mikagrel
Country: Australia
Language: English (Spanish)
Genre: Travel
Published (Last): 8 January 2013
Pages: 73
PDF File Size: 19.57 Mb
ePub File Size: 13.53 Mb
ISBN: 472-3-48681-686-8
Downloads: 37954
Price: Free* [*Free Regsitration Required]
Uploader: Mumuro

AD Datasheet and Product Info | Analog Devices

The overall gain of the system is reduced by 6 dB because only half of the signal is available to the input of the SAW filter. Figure 46 illustrates the value of adding input and output series resistors to help desensitize the resonant effects of board parasitics. The AD may also be used to transform a single-ended signal to a differential signal. One Technology Way, P. Due to environmental concerns, ADI offers many of our products in lead-free versions. T1 is a 1-to-1 impedance ratio balun used to transform a single-ended input into a balanced differential signal.

Evaluation Board Schematic Rev. RF transmission lines connecting the input and output networks must be designed to minimize stray capacitance.

Not Applicable Input Interface. Pricing displayed is based on 1-piece. The input signal is ac-coupled and applied to the INHI input. Do not connect to this pin. Model Package Pins Temp. If a model is not available for web samples, look for notes on the product page that indicate how to request samples or Contact ADI.


By applying a voltage to Pin 3 of header P1, the output common-mode voltage can be directly adjusted. Differential circuits inherently provide improved common-mode rejection and harmonic distortion performance as well as better immunity to interference and ground noise.

The power loss associated with these networks must be accounted for when attempting to measure the gain of the device. Sample availability may be better than production availability. The package for this IC i. To select the gain resistor and the feedback resistor, refer to Figure 38 and Figure Documents Flashcards Grammar checker. Resources AD Gerber Files.

Temperature Range This is the acceptable operating range of the device. Also, please note the warehouse location for the product ordered.

Low Distortion Differential RF/IF Amplifier AD8351 Data Sheet

For low resistive load or source resistance, the effective Q is lower, and higher relative capacitance termination or terminations can be allowed before oscillation or excessive peaking occurs. The device can be used as a general-purpose gain block, an ADC driver, and a high speed data interface driver, among other functions.

However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use.

This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. The isolation of each device when in a disabled state PWUP pin pulled low is about 60 dBc for the maximum input level of 0.


Output Reflection Coefficient vs.

The AD is datashfet to satisfy the demanding performance requirements of communications transceiver applications.

We achieve this by incorporating quality and reliability checks in every scope of product and process design, and in the manufacturing process as well. This is the acceptable operating range of the device. The model has been scheduled for obsolescence, but may still be purchased for a limited time. We do take orders for items that are not in stock, so delivery may be scheduled at a future dataeheet.

AD Datasheet pdf – Low Distortion Fully Differential RF / IF Amplifier – Analog Devices

The voltage gain can be set from unity to 26 dB using a single external gain resistor. For detailed drawings and chemical composition please consult our Package Site. The high impedance environment between the terminating resistors and device input pins must not have ground planes underneath or near the signal traces.

The resistor RF is required to balance the output voltages required for second-order cancellation datasheer the AD and can be selected using a chart see the SingleEnded-to-Differential Operation section. Output Compression Point, P1 dB, vs.

The schematic and datssheet board artwork are presented in Figure 48, Figure 49, and Figure Component Side Silkscreen Figure Gain Resistor Input 1.